Bearhugger 0 Posted June 26, 2020 Share Posted June 26, 2020 Hi, I have this problem: When playing online games the other players always teleport around. So, the connection is not stable. My own character is not laggy. It's like this for quite some time... I used "interactive mode" of the firewall for quite some time before that - no problem. Now, when using "automatic mode" this "lag" occurs. My router wants to communicate with my pc (over LAN cable), port 1900. If I allow that, online gaming seems fine. Problem is: Last time on our previous router it worked like that for only 3 weeks, then - when we changed our Wifi - "lag" was back. Now, I'm afraid to allow that port 1900 communication because my router or pc might get hacked (again). Regards Bear Link to comment Share on other sites More sharing options...
Administrators Marcos 5,231 Posted June 26, 2020 Administrators Share Posted June 26, 2020 Try the following: - export the current product configuration - reset settings to defaults - make sure that no custom firewall rules exist, the trusted zone is configured properly and that automatic policy mode is selected. Does the issue occur then? If so, does temporarily pausing the firewall make a difference? Link to comment Share on other sites More sharing options...
Bearhugger 0 Posted June 27, 2020 Author Share Posted June 27, 2020 (edited) It's pretty weird, as soon as I changed to "interactive mode" and changed back to automatic (because there were just too many decisions...) lag was back again. With firewall off lag was hardly noticeable! Edited June 27, 2020 by Bearhugger Link to comment Share on other sites More sharing options...
Most Valued Members peteyt 395 Posted June 27, 2020 Most Valued Members Share Posted June 27, 2020 5 hours ago, Bearhugger said: It's pretty weird, as soon as I changed to "interactive mode" and changed back to automatic (because there were just too many decisions...) lag was back again. With firewall off lag was hardly noticeable! If you go into setup - network - connected networks - what is the network set as e.g. public, home/office etc. If public, try setting to home network Link to comment Share on other sites More sharing options...
Bearhugger 0 Posted June 28, 2020 Author Share Posted June 28, 2020 It is "home network" Link to comment Share on other sites More sharing options...
Most Valued Members cyberhash 194 Posted June 28, 2020 Most Valued Members Share Posted June 28, 2020 1 hour ago, Bearhugger said: It is "home network" Have you checked the troubleshooter to see if anything is being blocked that shouldn't be ???SETUP > NETWORK PROTECTION > TROUBLESHOOTING WIZARD Link to comment Share on other sites More sharing options...
Bearhugger 0 Posted June 28, 2020 Author Share Posted June 28, 2020 ok, I reset all my settings, now I get this: see Screenshot. Not sure whether I should allow this... Link to comment Share on other sites More sharing options...
itman 1,740 Posted June 28, 2020 Share Posted June 28, 2020 (edited) 3 hours ago, Bearhugger said: I reset all my settings, now I get this: see Screenshot. Not sure whether I should allow this... Were these firewall rules generated as a result of opening Network Wizard and selecting the Unblock tab? The first rule I have no clue since the screen shot is in German. What is the protocol used in English please. Also you have marked out the remote connection data which is required to make a determination. The second rule appears to be for inbound multicast traffic in which the Remote section should be "Trusted Zone." Problem is Eset firewall already has a default rule for this. Remove the mark-out so the detail is shown. Edited June 28, 2020 by itman Link to comment Share on other sites More sharing options...
Bearhugger 0 Posted June 28, 2020 Author Share Posted June 28, 2020 (edited) Yes, I did exactly that: Unblock. The first rule is the IPv4 of my router, and all protocols (in english). The second one could be the IPv6 of my router... (I still wonder whether I should use "interactive mode", as that worked back in 2017; now it seems much more complicated...) Edited June 28, 2020 by Bearhugger Link to comment Share on other sites More sharing options...
itman 1,740 Posted June 28, 2020 Share Posted June 28, 2020 The problem with using the Network Wizard is it creates "permissive" rules. I question the IPv4 rule it created. As it stands now, the rule is allowing all inbound traffic from the router regardless of application being used. I would say this is a no-no. Link to comment Share on other sites More sharing options...
Most Valued Members Nightowl 206 Posted June 29, 2020 Most Valued Members Share Posted June 29, 2020 8 hours ago, Bearhugger said: Yes, I did exactly that: Unblock. The first rule is the IPv4 of my router, and all protocols (in english). The second one could be the IPv6 of my router... (I still wonder whether I should use "interactive mode", as that worked back in 2017; now it seems much more complicated...) I believe it is still the same Interactive Mode that worked for you back then , but maybe now it's more detailed. Link to comment Share on other sites More sharing options...
Bearhugger 0 Posted June 29, 2020 Author Share Posted June 29, 2020 Yea, I would need a guide for that 🙂 Link to comment Share on other sites More sharing options...
Recommended Posts